Buscar en
Hormigón y Acero
Toda la web
Inicio Hormigón y Acero From experiments to design: A probabilistic definition of design formulations fr...
Información de la revista
Compartir
Compartir
Descargar PDF
Más opciones de artículo
Visitas
1147
Acceso a texto completo
From experiments to design: A probabilistic definition of design formulations from empirical and semi-empirical resistance models
Desde experimentos hasta diseño: una definición probabilística de formulaciones de diseño a partir de modelos de resistencia empíricos y semiempíricos
Visitas
1147
Giuseppe Mancini
Autor para correspondencia
giuseppe.mancini@polito.it

Corresponding author.
, Vincenzo Ilario Carbone, Diego Gino
Department of Structural, Geotechnical and Building Engineering (DISEG), Politecnico di Torino, Turin, Italy
Este artículo ha recibido
Recibido 30 septiembre 2017. Aceptado 26 diciembre 2017
Información del artículo
Resumen
Texto completo
Bibliografía
Descargar PDF
Estadísticas
Figuras (4)
Mostrar másMostrar menos
Tablas (2)
Table 1. Statistical parameters and probabilistic distribution for the random variables affecting the resisting model.
Table 2. Comparison between the proposed method based on Monte Carlo simulation with N=106 samples and the analytical method proposed by [4].
Mostrar másMostrar menos
Abstract

The definition of design equations from empirical or semi-empirical resistance models is a matter of relevance for structural engineering. In common practice, the limit states design approach predicts the direct application of partial safety factors to the resistance of the materials in order to obtain design formulations coherent with a prescribed level of reliability. As empirical or semi-empirical models are calibrated, adjusting empirical coefficients to fit a set of experimental data, the application of partial safety factors to material properties alone is not able to provide a correct estimation of structural reliability.

In the present paper, a methodology based on the Monte Carlo method for probabilistic calibration of empirical and semi-empirical resistance models is proposed. Its application related to the probabilistic calibration of the semi-empirical model proposed by fib Model Code 2010 for the estimation of laps and anchorages tensile strength in reinforced concrete structures is reported and discussed.

Keywords:
Structural reliability
Empirical and semi-empirical models
Model uncertainties
Probabilistic calibration
Laps and anchorages
Resumen

La definición de las ecuaciones de proyecto a partir de modelos resistencia empírica o semiempírica es una cuestión de importancia para la ingeniería estructural. En la práctica común, el proyecto segun los estados límites prevee la aplicación directa de factores de seguridad parciales a la resistencia de los materiales, con el fin de obtener formulaciones de diseño coherentes con un nivel de fiabilidad prescrito. Como los modelos empíricos o semiempíricos se calibran ajustando los coeficientes empíricos para adaptarse a un conjunto de datos experimentales, la aplicación de factores de seguridad parciales a las propiedades de los materiales por sí sola no permite una estimación correcta de la fiabilidad estructural.

En el presente trabajo se propone una metodología basada en el método de Monte Carlo para la calibración probabilística de modelos de resistencia empírica y semiempírica. Su aplicación relacionada con la calibración probabilística del modelo semiempírico para la estimación de la resistencia a tracción de superposiciones y anclajes en estructuras de hormigón armado es reportada y comentada.

Palabras clave:
Fiabilidad estructural
Modelos empíricos y semiempíricos
Incertidumbres del modelo
Calibración probabilística
Vueltas y anclajes
Texto completo
1Introduction

Commonly, in structural engineering design formulations must always comply with a prescribed reliability level. To this end, physical or empirical and semi-empirical resisting models should be properly calibrated by the application of consistent safety formats.

The resisting models based both on physical laws (e.g. equilibrium of forces and kinematic compatibility) and on semi-empirical or empirical formulations (e.g. [1,2]) fitted on experimental results are really frequent in structural engineering.

In the limit states semi-probabilistic design approach [3], the safety requirements are fulfilled applying partial safety factors accounting for material properties and geometry statistical variability and model uncertainties. Concerning the resisting models based on physical assumptions, the direct application of partial factors to materials strength leads to design expressions consistent with a specific reliability level. This does not happen in the case of empirical or semi-empirical resisting models that are based on experimental test set. In such kind of models, all the empirical coefficients embedded in the formulation are calibrated as best fitting on the experimental results and assuming mean values of material properties (i.e. the actual values measured during the experiment execution). In this case, it implies that the direct application of partial safety factors to materials strength does not lead to a proper evaluation of reliability.

In the literature, several methodologies for probabilistic assessment of physical, empirical and semi-empirical models are proposed [4–6]. In order to apply these theoretical procedures consistently, an accurate assessment of model uncertainties is necessary as proposed in [7–11].

However, a general and ease-to-apply procedure able to calibrate empirical or semi-empirical formulation in relation to a specific level of reliability is still not available and defined.

In the present paper a methodology based on the Monte Carlo method [12] for calibration of empirical and semi-empirical resisting models is proposed. This procedure is able to account for both statistical variability of material and geometric properties and the influence of the resisting model uncertainties. After the detailed description of the methodology, its application to the calibration of the semi-empirical model for laps and anchorages tensile strength evaluation suggested by Model Code 2010 [13] is proposed and commented.

2Methodology for the assessment of design expressions from empirical or semi-empirical resisting models

In this section the methodological approach for probabilistic calibration of empirical and semi-empirical models is described.

The proposed methodology grounds on four main points:

  • -

    the individuation of the empirical or semi-empirical resisting model;

  • -

    the definition of the probabilistic model;

  • -

    the definition and characterization of the resistance random variable;

  • -

    the estimation of the fractiles of the resistance random variable and determination of the design expressions.

2.1Individuation of the empirical or semi-empirical resisting model

In general, an empirical or semi-empirical resting model is calibrated grounding on a set of experimental results and the estimated value of the resistance Rmodel can be expressed in the following form:

where C is best fitting empirical coefficient calibrated on the experimental database; Xi is a set of K random variables which plays a significant role in the resisting model (i=1, 2, , K); f(X1,m, X2,m, , Xi,m, …, XK,m) is a function of the abovementioned random variables assumed with their mean or experimental value; A is a function of all the parameters that can be assumed as deterministic (e.g. geometry).

The value of Rmodel estimated by means of Eq. (1) should be intended as a mean resistance as it is calculated assumed mean or experimental material properties and empirical coefficients fitted on experimental tests. Then, the direct application of Eq. (1) for design purposes it is not correct as it is deprives of any safety assumption.

2.2Definition of the probabilistic model

Once all the parameters that can influence the resisting model with their statistical variability are selected, the following vector of random variables X can be defined:

The vector of random variables X includes also the model uncertainty random variable ϑ that should be calibrated base on the statistical assessment of the ratio between experimental results and model predictions according to [14]. The vector of random variables X can group both statistically independent and statistically dependent random variables.

All the random variables grouped in X have to be represented by their probabilistic distribution (i.e. PDFs and/or CDFs) which must be able to describe their statistical variability accurately.

Suggestions for the definition of the probabilistic model can be acknowledged by [14].

2.3Definition of the resistance random variable

The resistance random variable can be evaluated in function of the vector X descending from Eq. (1) as follow:

The expression reported by Eq. (3) is able to represent the random variability of the resistance accounting for material statistical fluctuations and model uncertainties. However, in order to propose a not case dependent and general procedure, the following ratio has to be addressed:

where ζ(X) is the resistance ratio random variable and (X1,rep, X2,rep, …, Xi,rep, …, XK,rep) are the representative values of the main random variables (e.g. 5% characteristic or nominal value).

The random variable ζ(X) can be assessed by means of the Monte Carlo method [11] sampling from the probabilistic distributions of the random variables involved by Eq. (4). When a significant number of samples of the population of ζ(X) is available, the most suitable probabilistic distribution able to describe ζ can be selected.

2.4Estimation of fractiles of the resistance random variable

In order to define relationships for design purposes, it is convenient to assess particular fractiles from the resistance random variable.

This can be performed defining the following probability:

where ζp is the fractile related to a certain probability to not be exceeded of the random variable ζ(X); p represent the probability of not exceedance for the value of ζp.

In common engineering practice and according to international codes [15,13], the following fractiles of ζ(X) are estimated:

  • -

    characteristic value ζk, setting p=0.05;

  • -

    design value ζd, setting p=Φ(−αR·β);

with β reliability index [16], αR first order reliability method (FORM) correction factor (assumed equal to 0.8 for dominant resistance variables) [13] and Φ(·) cumulative standard normal distribution.

Once the probabilistic coefficient ζp has been estimated, the general formulation for the selected fractile of the resistance random variable Rp can be expressed as follow:

3Application example: laps and anchorages tensile strength in fib Model Code 2010

In this section, an example of application of the procedure so far described is reported. Usually, in reinforced concrete structures, due to technical and construction reasons, it is required to interrupt the longitudinal tensile steel reinforcements. It is then necessary to provide an adequate length of overlapping or anchorage in order to allow continuity in the transferring of forces within the structure.

In [13,17] the evaluation of the maximum tensile strength of a lapped joint or anchorage can be assessed by means of a semi-empirical formulation. Subsequently, the proposed methodology will be applied for the calibration of the abovementioned resisting model.

3.1Laps and anchorages tensile strength formulation in Model Code 2010

In the fib Model Code 2010 [13] the evaluation of laps and anchorages tensile strength fstm is performed by means of the semi-empirical model proposed in [17], that is a modification of the approach suggested in [18] based on [19,20].

The best-fitting semi-empirical expression for laps and anchorages strength estimation, which is calibrated on a large set experimental results [21], is represented by Eq. (7):

where fcm is the mean concrete compressive strength; lb is the lap/anchorage length; Φ is the bar diameter; concrete covers cmin, cmax and effectiveness coefficient km are evaluated according to Fig. 1(a and b).

Figure 1.

Determination of concrete cover cmin and cmax in Eq. (1) (a) and assessment of the effectiveness of shear links (b).

(0,1MB).

The coefficient Ktr accounts for the effect of confinement provided by shear links/stirrups situated along the lap or anchorage and can be calculated as follow:

where nl is the number of legs of a link/stirrup; ng is the number of groups of links/stirrups; Asv is the transverse area of each leg of a link/stirrup; nb is the number of individual anchored bars of pairs of lapped bars.

The assessment of Eq. (7) have been performed base on an experimental database counting more than 800 tests on laps and anchorages coming from American (ACI) and European investigations [21]. In the fib Bulletin No. 72 [17] are provided the following limits for Eq. (7) as they represent also the limits of the abovementioned database:

  • -

    15MPafcm110MPa;

  • -

    Ktr0.05;

  • -

    0.5cmin3.5 and cmax/cmin5;

  • -

    lb10Φ;

  • -

    25/Φ2.

3.2Probabilistic model

As reported in Section 2, a set of relevant random variables have to be defined. These random variables have to represent parameters that are explicitly considered into the resisting model.

In this case, may be reasonable consider as random variable only the concrete compressive strength, which strongly affect the resisting mechanism with its statistical variability. At the purpose of this example all the other parameters involved by Eq. (7) can be assumed as deterministic.

However, the resisting models shows an intrinsic uncertainty due to simplified assumptions in their definition and in disregarding parameters that can have some influence on the actual resisting mechanism. This involves that the resisting model uncertainties have to be accurately addressed and included into the probabilistic model.

Therefore, in the present application the following random variables will be considered in the vector X:

where:
  • -

    fc, is the cylinder compressive strength random variable. According to fib Model Code 2010 [13] the statistical variability of fc can be described by means of a log-normal distribution with coefficient of variation Vc equal to 0.15 and mean value equal to fcm depending by the concrete strength class (Table 1).

    Table 1.

    Statistical parameters and probabilistic distribution for the random variables affecting the resisting model.

      Ref.  Mean value  C.o.V  Type of distribution 
    Concrete compressive strength, fc [MPa]  [13]  fcm  0.15  Log-normal 
    Model uncertainties, ϑ [–]  [22]  0.98  0.13  Log-normal 
  • -

    ϑ, is the resisting model uncertainty random variable. In compliance with JCSS Probabilistic Model Code [14] the statistical characterization of ϑ can be performed defining the following ratio:

where RExp is the actual resistance estimated from laboratory tests and RModel is the resistance estimated by the model.

The model uncertainties related to Eq. (7) have been estimated base on the database of experimental results reported in [21]. The mean value μϑ and the coefficient of variation Vϑ are listed in Table 1 according to the statistical investigation proposed by [22] concerning the case of new structures. According both with [22,14]ϑ can be described by means of a log-normal distribution.

3.3Resistance random variable

Defining the resistance random variable R as the lap or anchorage tensile strength fst, according with Section 2, Eq. (7) can be rewritten as follow:

with:

and the empirical coefficient C set equal to 54.

Defining as the representative value for concrete compressive strength the characteristic one, the resistance ratio random variable ζ(X) can be determined as subsequently reported:

where fck is the 5% characteristic value for cylinder concrete compressive strength.

By means of Monte Carlo technique it is possible to generate a large sample of the population of the random variable ζ(X).

In the present example a number of samples N equal to 104, 106 and 108 has been generated adopting the direct Monte Carlo sampling from the probabilistic distributions of the basic variables listed in Table 1. The associated relative frequency histogram is reported in Fig. 2.

Figure 2.

Relative frequency histogram for the Monte Carlo simulation of the random variable ζ(X) in the hypothesis of 104, 106 and 108 samples.

(0,09MB).

As R(X) is a function of two log-normally distributed random variables (i.e. fc and ϑ), it is expected that ζ(X) is log-normally distributed too [4].

A shown by Fig. 2, the results obtained adopting 104, 106 and 108 samples give not appreciable difference in the estimation of the distribution parameters for the random variable ζ(X). Being the total number of samples required for the Monte Carlo simulation inversely proportional to the probability of failure to be estimated, a number of samples set N=106 can be considered sufficient for the present investigation (as, in Section 3.4, the minimum estimated probability is around 10−3, which corresponds to the fractile of the distribution of ζ(X) associated to the value of the product αR·β with β=3.8 and αR=0.8).

However, in the case of the estimation of smaller probability of failure, a larger number of samples is recommended in order to represent, inside the sample, also lower extreme values of the involved random variables.

Finally, concerning the population with 106 samples of the random variable ζ(X), the Chi-square goodness of fit test with 5% level of significance testing the hypothesis of normality of the sample of ln(ζ(X)) have been performed confirming the hypothesis of log-normality of the variable ζ(X). Hence, the resistance ratio random variable ζ(X) can be described by means of a lognormal distribution having mean value equal to 0.98 and coefficient of variation (C.o.V) equal to 0.13 (Fig. 3(a and b)).

Figure 3.

Log-normal distribution (PDF (a) and CDF (b)) for the random variable ζ(X).

(0,12MB).
3.4Derivation of the characteristic and design expressions

Once the probabilistic distribution for the random variable ζ(X) has been determined and characterized, it is possible to calculate its fractiles as described by Eq. (5). In Table 2 are reported the 5% characteristic value ζk and design value ζd (assuming the reliability index β=3.8 as in the case of ordinary structures with 50 years service life [13,15]. The abovementioned values have been compared in Table 2 with the results coming from the simplified analytical procedure proposed by Taerwe [4] (which was applied in [22] to Eq. (7)) valid in the case of log-normally distributed random variables.

Table 2.

Comparison between the proposed method based on Monte Carlo simulation with N=106 samples and the analytical method proposed by [4].

  Proposed  [4,22] 
  N=106   
ζk [–]  0.78  0.83 
ζd [–] (αR=0.8; β=3.8)  0.65  0.69 

The simplified analytical method [4,22] leads to results close to the ones obtained with the simulation technique. However, the proposed methodology can be easily applied in case of probabilistic distributions for main random variables different from the log-normal one.

As international codes [3,13,23] suggests different levels of reliability distinguishing between new or existing structures in function of the service life of the structure, it is useful to define the trend of variation of the design probabilistic coefficient ζd versus the reliability index β. The variation of ζd in function of the reliability index β in proposed in Fig. 4. The calibration of the design expressions related to original semi-empirical model (Eq. (7)) can be performed specifically in function of the target reliability level.

Figure 4.

Variation of the design probabilistic coefficient ζd in the function of the reliability index β.

(0,08MB).

Finally, the 5% characteristic fst,k and the reliability-based design fst,d expressions for the semi-empirical model proposed by [17,13] for laps and anchorages tensile strength estimation can be evaluated as follow according to Eq. (6) and Table 2:

4Conclusions

A probabilistic procedure based on the Monte Carlo method for the derivation of design formulas by empirical or semi-empirical resisting models has been proposed. The procedure allows the correct evaluation of the influence of material and resisting model uncertainties in the reliability-based calibration of the abovementioned kinds of resisting models.

This result can be obtained by means of the definition of multiplicative probabilistic coefficients ζp, which are related to a specific probability of not exceedance p. As the probability p is directly related to a certain value of the reliability index β, the final design equations can be derived in function of the level of reliability required by the codes.

The proposed procedure is very general as it is independent from the probabilistic model defined for the main random variables. Furtherly, it is suitable for the calibration of design formulations both in the case of serviceability and ultimate limit states.

Acknowledgements

This work is part of the collaborative activity developed by the authors within the framework of Task Group TG 3.1 of the Fédération Internationale du Béton (fib).

References
[1]
A. Muttoni, M.F. Ruiz.
Shear strength of members without transverse reinforcements as function of critical shear crack width.
ACI Struct. J., 219 (2008), pp. 163-172
[2]
G. Bertagnoli, G. Mancini.
Failure analysis of hollow core slabs tested in shear.
Struct. Concr., 10 (2009), pp. 139-152
N° 3
[3]
EN 1990 Eurocode: Basis of Structural Design, Brussels.
(2002),
[4]
R.L. Taerwe.
Toward a consistent treatment of model uncertainties in reliability formats for concrete structures.
CEB Bull. d’Information, (1993), pp. 5-34
N° 105-S17
[5]
S. Junho, K. Won-Hee.
Probabilistic shear strength models for reinforced concrete beams without shear reinforcements.
Struct. Eng. Mech., 34 (2016), pp. 15-38
[6]
R.L. Taerwe.
Partial safety factor for high strength concrete under compression.
Proceedings of High Strength Concrete 1993, pp. 385-392
[7]
G. Köenig, J. Fischer.
Model uncertainties concerning design equations for the shear capacity of concrete members without shear reinforcement.
CEB Bull. d’Information, (1995), pp. 49-94
N° 224
[8]
C.H. McLeod, C. Viljoen, J.V. Retief.
Quantification of model uncertainty of EN1992 crack width prediction model.
Insights and Innovations in Structural Engineering, Mechanics and Computation, (2016), pp. 1349-1354
[9]
M. Sikora, M. Holicky, M. Prieto, P. Tanner.
Uncertainties in resistance models for sound and corrosion-damaged RC structures according to EN 1992-1-1.
Mater. Struct., (2014), pp. 3415-3430
N° 48
[10]
D.L. Allaix, V.I. Carbone, G. Mancini.
Modelling uncertainties for loadbearing capacity of corroded simply supported RC beams.
Struct. Concr., (2015), pp. 333-341
N° 3
[11]
D. Gino, G. Bertagnoli, D. La Mazza, G. Mancini.
A quantification of model uncertainties in NLFEA of R.C. shear walls subjected to repeated loading, Ingegneria sismica.
International Journal of Earthquake Engineering, (2017), pp. 79-91
Anno XXXIV, Special issue
[12]
M.H. Kalos, P.A. Whitlock.
Monte Carlo Methods, Vol. 1: Basics.
John Wiley & Sons, (1986),
[13]
fib: fib Model Code for Concrete Structures 2010, Lausanne.
(2013),
[14]
JCSS.
JCSS Probabilistic Model Code.
(2006),
[15]
CEN: EN 1992-1-1: Eurocode 2 – Design of Concrete Structures. Part 1-1: General Rules and Rules for Buildings.
CEN, (2004),
[16]
A.M. Hasofer, N.C. Lind.
Exact and invariant second moment code format.
J. Eng. Mech. Div. ASCE, 100 (1974), pp. 111-121
[17]
fib Bulletin N°72: Bond and Anchorages of Embedded Reinforcements – Background to the fib Model Code for Concrete Structures, Lausanne.
(2015),
[18]
E. Canbay, R.J. Frosch.
Bond strength of lap-spliced bars.
ACI Struct. J., 102 (2005), pp. 605-614
[19]
S. Lettow.
Ein Verbundelement für nichtlineare Finite Element Analysen – Anwendung auf Übergreifungsstöße.
University of Stuttgart, (2006),
(Dissertation)
[20]
C.J. Burkhardt.
Zum Tragverhalten von Übergreifungsstößen in hochfestem Beton.
RWTH, (2000),
(Dissertation)
[21]
fib TG 4.5 Bond Tests Database.
(2005),
[22]
G. Mancini, V.I. Carbone, G. Bertagnoli, D. Gino.
Reliability-based evaluation of bond strength for tensed lapped joints and anchorages in new and existing reinforced concrete structures.
Struct. Concr., (2017), pp. 1-14
[23]
ISO 2394: General Principles on Reliability for Structures, Genéve.
(1998),
Copyright © 2018. Asociación Española de Ingeniería Estructural (ACHE)
Opciones de artículo
Herramientas